![]() Operating Temperature: -10☌ to 55☌ (14☏ to 131☏)įor more specifications, visit. Night Vision: 30 Meters (100ft) Day/Night Mode: Auto Switchover If these won’t work, contact Reolink Support. Make sure that your PC is working on a stable network.Make sure that you download the correct firmware from Download Center.Check out the current camera firmware and see if it is the latest one.If you fail to upgrade the firmware for the camera, try the following solutions: Restore the camera to factory settings and check out the infrared light settings again.Upgrade the firmware of your camera to the latest version.Check if the Day/Night mode is enabled and set up auto infrared lights at night on Live View page via Reolink App/Client.Enable infrared lights on Device Settings page via Reolink App/Client.If the Infrared LEDs of your camera stop working, please try the following solutions: Try again with another Ethernet cable.If the camera is connected to a PoE device as listed above, connect the camera to another PoE port and see if the camera will power on.The PoE camera should be powered by a PoE switch/injector, the Reolink NVR or a 12V power adapter. Make sure your camera is powered properly.If your camera is not powering on, please try the following solutions: NOTE: If your camera has another mount without the adjusting knob, please loosen the adjusting screw with the provided hex key and turn the camera as shown below to adjust the angle. Stiffen the adjustment knob to lock the camera. To get the best field of view, loosen the adjustment knob on security mount and turn the camera. ![]() NOTE: Run the cable through the cable notch on the mount base. Install the mount base with the mounting screws included in the package. NOTE: Use the drywall anchors included in the package if needed. Please check out the mount included in the package and follow the corresponding instruction to install the camera properly.ĭrill holes in accordance with the mounting hole template. NOTE: There are two different types of mounts for bullet cameras. You may power on the camera indoors for a few minutes before installing it outdoors. Because when it is powered on, the camera will produce heat. The camera may work in extreme cold conditions as low as -25☌.Do not install the camera at places where rain and snow can hit the lens directly.However, it doesn’t mean the camera can work underwater. With IP waterproof ratings, the camera can work properly under conditions like rain and snow.Make sure the power ports are not directly exposed to water or moisture and not blocked by dirt or other elements.To ensure better image quality, it’s recommended to clean the lens with a soft cloth from time to time.To ensure best image quality, the lighting condition for both the camera and the capture object shall be the same. Do not place the camera in a shaded area and point it towards a well-lit area.Or, it may result in poor image quality because of the window glare by infrared LEDs, ambient lights or status lights. Do not point the camera towards a glass window.Do not face the camera towards any light sources.NOTE: If you are connecting the camera to a Reolink PoE NVR, please set up the camera via the NVR interface. Set up the Cameraĭownload and Launch the Reolink App or Client software, and follow the onscreen instructions to finish initial setup.ĭownload path of the Reolink Client: Go to > Support > App & Client. NOTE: The camera should be powered with a 12V DC adapter or a PoE powering device such as PoE injector, PoE switch or Reolink NVR (not included in the package). Note: Reolink Client is compatible with NVRs and IP Cams from Reolink.*You may also connect the camera to a PoE switch or Reolink PoE NVR. Schedule video recording (including motion-triggered recording) at anytime.ġ0.Ĝontrol PTZ (pan-tilt-zoom) cameras remotely (left, right, up and down). Remotely playback video recording from your camera SD card and NVR HDD.ħ.Ĝapture video from Live View channels to playback.Ĩ.Ĝapture single and multiple images to save on your Mac.ĩ. Allow you to get 24/7 continuous recording on your Mac.ĥ.Ğnable you to review 4-channel recorded video at the same time.Ħ. Remotely monitor and watch live streaming on Mac anywhere and anytime.Ĥ. Only 3 steps to access cameras and NVRs (at the same local network) - the easiest solution ever.Ģ.Ğasy and friendly interface for all users to use.ģ. It allows you to get 24/7 continuous recording in your computers.ġ. You can monitor and watch live streaming of your home and business anywhere and anytime. It enables you to locally or remotely access your IP cameras and NVRs on Mac computers. Reolink Client is an easy-to-use security camera system surveillance software.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |